
What a roof inspection checklist covers
A home roof inspection checklist is the order a roofer works through a roof. It starts at the gutter line, moves along the eaves and valleys, checks every flashing point, and ends in the attic looking for daylight and staining on the sheathing. The gutter and downspout check comes first because everything below the roofline depends on water leaving it cleanly. A roof flashing check comes next, at every wall, chimney and vent pipe, since that is where most leaks start.
Signs of roof damage show up before a leak ever reaches a ceiling. Granules collecting at the downspout outlet, a shingle tab lifting along a rake edge, a slipped tile, or a dark ring on the attic sheathing each point to one spot on the roof. A shingle condition check looks at whether a tab still bends without cracking at the corner. An annual roof inspection checklist catches most of this before a storm, not after one. When wind has already pulled material loose overnight, after-storm roof inspections cover that situation instead of a routine walkthrough.
On a tile roof, the attic inspection points matter as much as anything visible from the ground. Missing or broken bird stops at the first course of tile let pigeons and other birds work their way underneath. A blocked eave stops water from draining the way the roof was built to drain. Hot, dry summers here bake that debris in place until the first real storm finds the blockage fast.
Gutters packed with debris are the detail a roof inspection checklist starts with, because the consequence runs downhill from there. Packed gutters make water back up behind the drip edge instead of draining off the roof. That standing water softens the fascia and the bottom edge of the decking until the first course of shingles has nothing solid left to hold its nails.
Once that happens, a Santa Ana wind gust can lift the whole bottom row instead of one tab. A gutter spilling over in ordinary rain is already a red flag. The same goes for shingles that look uneven from the ground, so call before the next wind arrives.
A spring roof inspection after the rainy season and a pre-storm roof inspection before wind season cover the two points when this checklist matters most. A roof maintenance programs schedule bundles both visits so the gutter and flashing checks happen before debris builds up again, instead of after a leak shows up on the ceiling.
The CSLB License Lookup publishes the rules that govern work like this in your area.


How the roof inspection visit works
The visit follows the same order as the checklist above, from the eave to the attic hatch, so nothing gets checked twice and nothing gets skipped.
- Our crew inspects gutters and downspouts for clogs and proper flow.
- Our inspection covers flashing at each chimney, vent pipe, skylight and wall.
- Our crew reviews shingle or tile condition over the entire roof surface.
- Our technician scans the attic using a flashlight to spot daylight, stains and rust on nails.
- Our team tests moisture levels under the sheathing with a pin meter wherever stains appear.
The attic lighting and nail check often reveal more than any ground-level review. Clean nail shanks with no staining mean the roof covering itself is the only question left. Rust on the nail tips with a dark ring around each one means warm, moist attic air has been condensing there, which points to a ventilation problem rather than the shingles. The pin moisture meter backs that finding up. A reading over 20 on a sheathing panel means that wood is already wet and losing strength. A reading below 15 means it is still dry and sound.
Where a shingle has to be replaced rather than patched, the usual choice over three tab is an architectural laminated shingle. Two layers glued together make it heavier and thicker than a three tab shingle, with wind performance commonly rated in the 110 to 130 mph range once it is installed with the specified nailing pattern and starter strip. Architectural laminated shingles are built to that heavier spec, with a longer average roof lifespan than three tab, which is why such shingles are the default residential choice.
A roof inspection by itself does not commit you to anything. It names which items on the checklist pass, which ones need a repair at one spot, and which ones mean the whole run of shingle or tile has reached the end of its service. That distinction, more than any single reading, decides whether the next call is for a patch or a full roof.
Steps in a roof inspection visit

On site assessment
We start outside at the gutters, move up through the flashing points and across the shingle or tile field, then finish in the attic with a light and a pin moisture meter. You can watch from the ground or from inside the attic hatch as we go. Anything that reads wrong, a soft spot, a stain, a rusted nail, gets a second look before we move to the next section. By the time we are done, the cause is named and you have a quote in hand for anything that needs attention.
Repair or replacement
Once you approve the quote, the work that needs doing comes first: clearing and resetting a bird stop, replacing a cracked boot, or pulling a section of tile to get at the decking under it. A spot repair gets isolated to that part of the roof, with surrounding tile or shingle lifted and set aside rather than broken. If the decking underneath turns out to be soft, we pause there and show you the bad section before anything new goes down over it.
Final check
Before we call it finished, the pin moisture meter goes back on any decking that was replaced or exposed. It has to read under 15 percent before that section gets covered again. We show you that reading on the spot, along with any bird stops, boots or flashing that got replaced. If a shingle or tile section was pulled to get there, you see it go back down in the same pattern it came off in, so the repair does not stand out from the rest of the field.
What a roof inspection needs in Ontario homes
Swapping out a few shingles rarely triggers paperwork. A deck replacement or a full tear off is different: the City of Ontario Building Department has to review that job, working from the California Residential Code, before it closes out.
Houses from the 1945 to 1970s era carry low pitch roofs that were never built with much margin, so a handful of lifted shingles on one of these can mean the field is close to the end of its life everywhere else too. Tile roofs from the 1980s and 1990s hide their real problem under the tile: the underlayment ages out while the tile itself still looks fine from the ground, so a visual check alone misses it.
For help with the job itself, read about after-storm roof inspections.
What to expect from this visit
Scheduling your inspection visit
On the call we ask whether you are dealing with an active leak or just want the checklist run before a storm. An active roof leak gets a technician out that same day. A routine walkthrough gets set up around your schedule instead. Either way we ask what you are seeing and when it started, since that shapes how the attic and the roof get checked.
What gets moved for access
Checking the roof means a ladder going up against the eave and someone walking the attic for part of the visit. Open a clear route to the attic opening and shift stored items out from beneath it. Outside, we need clear ground near the eaves to set the ladder, so move potted plants or anything breakable away from that wall before we arrive.
Sizing a repair or replacement
A roof with several valleys, a chimney, dormers and a skylight takes longer to check and longer to repair than one open field of shingle. Every one of those is a separate flashing point that can fail on its own. The checklist tells us whether the problem sits at one of those penetrations or across the whole field. Once we know which, you see that finding in writing and approve it before anything on the roof changes.
What you are shown on site
We point out what we found, on the roof or in photos from the attic, before we leave. If a repair means opening up tile or shingle to reach decking, we ask before any of it comes up. Anything that gets replaced, like a section of bad decking, gets shown to you rather than bagged and hauled off without a look.
Roof Inspection Checklist Questions From Ontario Homeowners
A checklist for any home or condo roof follows the same order, gutters first, then flashing, then the field, then the attic. We check downspouts for debris and flow, look at every wall, chimney, vent pipe and skylight for flashing wear, and check shingle or tile condition across the field. Inside the attic, a light shows daylight, staining or rust on nail tips, and a pin moisture meter checks any stained sheathing. Readings under 15 percent mean dry decking, and above 20 percent means that section is holding water.
A spongy or springy feel underfoot between rafters fails a safety check, since that means the sheathing has delaminated or rotted under it. Rusted nail tips with dark rings around them point to moisture condensing in the attic all winter. A pin moisture meter reading above 20 percent on decking means that section is compromised and needs attention before anything goes back over it. Cracked shingle tabs that lose granules when lifted, and standing water still sitting two days after rain on a low slope section, are also flags during a walkthrough.
Home inspectors follow the roof's drainage order from gutter to attic. They check downspouts for flow, then flashing where the roof meets walls, chimneys, vent pipes and skylights, then the shingle or tile field for lifted tabs and cracked corners. In the attic, a light checks for daylight at penetrations, clean nail shanks and staining on the sheathing. Where we see staining, the meter pins go into the decking from below to tell dry wood from wet.
Layer count on a re-roof is set under the California Residential Code. The City of Ontario Building Department makes the final call once a job involves a deck replacement or full tear off. Swapping a few shingles rarely triggers that review, but stacking layers changes how much weight the deck and framing carry. A tear off assessment looks at the decking underneath rather than just the visible covering. The attic light and nail inspection, along with a pin moisture meter reading, show whether that decking is sound enough to build back on.
Gutter flow and flashing points matter most, since water intrusion often begins at those spots. After that, the shingle or tile field gets checked for lifted tabs, cracked corners and granule loss. Inside the attic, a light checks for daylight and staining, and a pin moisture meter confirms whether any stained sheathing is still dry or already wet. On tile roofs, bird stops at the eave corners need the same attention, since a missing one lets debris and water pack in behind the first course.
A roof inspection covers gutters, flashing points, and the full shingle or tile field. It finishes with a light and a pin moisture meter check in the attic. That check looks for gaps at penetrations, rust on nail tips and dark staining that points to a ventilation problem rather than the roof covering. Any stained sheathing gets a moisture reading, with a result over 20 percent marking that section as wet and under 15 percent reading as dry. The findings separate a spot repair from a full replacement.
Why eave debris changes roof inspections in Ontario
Ontario's hot summers push roof temperatures well above 100 degrees, causing materials to expand and contract. Strong Santa Ana winds each fall and winter can lift loose shingles or tiles. That has little to do with the roof itself. What matters up there is the climate above it. Hot, dry summers bake dust and plant debris into anything sitting in a gutter or packed behind a bird stop, and that crust does not move again until rain gets heavy enough to push it. Fall and winter bring most of the year's rain in a short stretch, so a gutter that has been collecting all summer gets tested hard and fast, right when a Santa Ana wind event is also likely to be lifting tile or shingle at the same time.
An inspection by itself does not get reviewed by any office, since it is a condition report rather than permitted work. The paperwork only starts once a finding turns into a repair that opens up decking or changes the covering, and that is the point oversight applies. That is also why the checklist records a reading. A pin moisture meter number on a decking panel holds up with an inspector or an insurance adjuster in a way that a soft looking spot does not. That distinction tells you up front whether what you are looking at is paperwork or just maintenance.
Roofing Services Near Ontario
Still deciding what your Ontario home needs? Call (909) 330-4661 and we will talk it through before anyone books a visit.
Address:
Ontario Roofing, 4335 E Lowell St, Suite G
More Roofing Guides for Ontario Homeowners
- Storm Season Roof Prep Guide
- Roof Replacement Cost Guide 2026
- Metal vs. Shingle Roofing
- Insurance Claim Guide for Roof Damage
- How Long Does a Roof Last
- Signs You Need a New Roof
- How to Choose a Roofing Contractor
- Roof Financing Options Explained
- Reading a Roofing Proposal Line by Line
- TPO vs. EPDM, Which Flat Roof Is Best
- Energy-Efficient Roofing Guide
- Roof Ventilation Basics
- DIY vs. Professional Roof Repair
- Understanding Roofing Estimates
- All roofing guides
- Wind Damage Roof Repair
- Roof Replacement
- Storm Damage Roof Repair
From the ground, zoom in with a phone camera or binoculars at the eave line and look for gaps where tile meets tile. A dark gap or a visible nest means a bird stop is missing or broken. That check stops there. Pulling tile, walking the field or getting into the attic to confirm what is underneath belongs to the visit, since a loose tile on a walked roof is how falls happen.
Know whether you have seen water inside, or just suspect something from outside. Note when you first noticed a shingle, tile or gutter issue, and whether a storm or wind event came through right before it. If you know the roof's age or material, have that ready too, along with where the attic hatch is inside the house.
